Pool Finish -Plaster

Calm Sea.

Cement Mix 65 Pounds

Additional DescriptionMore Details

You need 5 Gal Bond Kote Resin per 2 Bags. SGM Bond Kote is a specially formulated two part cementitious coating, designed to be used as an ideal substrate to mechanically bond pool plaster over existing plaster finishes. CHARACTERISTICS: • Superior bonding capability • High flexural strength • Eliminates excessive substrate preparation • Virtually eliminates delamination problems • Saves labor and equipment costs • Provides even dry time while plastering LIMITATIONS: All materials and surfaces to be coated should remain between 40 degrees F/120 degrees F 24 hours prior and 24 hours after installation. Do not apply in rain or extremely high humidity. Protect “Liquid Resin” from freezing. Plaster should be applied to Bond Kote within 14 days or reapply Bond Kote. DO NOT USE OVER PAINTED OR PLASTIC FINISHES. PACKAGING: SGM Bond Kote is formulated in units consisting of two 65 lb. bags of a factory blended dry cement mix and one 5 gallon container of “Liquid Resin”. These ingredients are mixed at jobsite as per mixing instructions. SURFACE PREPARATION: Check completely for hollow areas and remove all loose plaster. Remove all mildew, algae, fungus and rust by either sand blasting or with an acid wash which must be followed by neutralization with soda ash. If surface is unusually soft, painted, peeling or flaking, then surface must be heavily sanded or water blasted. Regardless of method used, thoroughly wash down with “jet nozzle” hose and let pool drain until there is no standing water present. NOTE: Special attention is required on pools below water table and or leaking. MIXING: • Make sure “liquid resin” is mechanically agitated before use to disperse all settled solids. • Then pour “liquid resin” (5 gallon) into a clean mixing container with flat bottom. Add Bond Kote (two 65 lb. bags) while continuously mixing with echanical mixer. Continue mixing for 2-4 minutes until Bond Kote is completely dispersed. NEVER USE LESS • THAN 115 lbs. OF DRY MIX PER 5 GALLONS OF LIQUID RESIN. APPLICATIONS: To check consistency of material, apply Bond Kote with 1-1/4″ nap roller onto a vertical test area. Let material set for 1 minute; then, using a clean textured roller, rough up surface to desired finish. Material thickness can be adjusted by adding a small amount of “cement mix” if too thin or “liquid resin” if too thick, adjust only 1 time. DO NOT RETEMPER MIX. Once Bond Kote is mixed to correct consistency, apply immediately, do not let material stand unused. Apply, mixed Bond Kote with 1-1/4″ nap roller to steps at shallow end of pool and let material set for approximately 1 minute; then, rough up surface to desired finish with clean textured roller as done in test area. Continue this same process with the wall areas and then proceed to the floor surface last. Starting at deep end of pool make sure application is uniform in thickness and texture. CURING: Minimum cure is reached in 6 hours; setting and drying time may vary according to atmospheric conditions. For best results wait 24 hours before plastering. PLASTERING: Mist Bond Kote with clean cool water prior to plastering to permit proper hydration. Make sure Bond Kote is free of any foreign matter before plastering. COVERING: One unit covers 450-500 square feet of surface area. CLEAN UP/STORAGE: Clean hands, tools and containers with warm soapy water. NOTE: USE NEW ROLLER WITH EACH APPLICATION.

Price: $15.55

Loading Updating cart…

SGM Bond Kote Resin.

5 Gal Container
Liquid Resin.

Additional DescriptionMore Details

You need 5 Gal Bond Kote Resin per 2 Bags. SGM Bond Kote is a specially formulated two part cementitious coating, designed to be used as an ideal substrate to mechanically bond pool plaster over existing plaster finishes. CHARACTERISTICS: • Superior bonding capability • High flexural strength • Eliminates excessive substrate preparation • Virtually eliminates delamination problems • Saves labor and equipment costs • Provides even dry time while plastering LIMITATIONS: All materials and surfaces to be coated should remain between 40 degrees F/120 degrees F 24 hours prior and 24 hours after installation. Do not apply in rain or extremely high humidity. Protect “Liquid Resin” from freezing. Plaster should be applied to Bond Kote within 14 days or reapply Bond Kote. DO NOT USE OVER PAINTED OR PLASTIC FINISHES. PACKAGING: SGM Bond Kote is formulated in units consisting of two 65 lb. bags of a factory blended dry cement mix and one 5 gallon container of “Liquid Resin”. These ingredients are mixed at jobsite as per mixing instructions. SURFACE PREPARATION: Check completely for hollow areas and remove all loose plaster. Remove all mildew, algae, fungus and rust by either sand blasting or with an acid wash which must be followed by neutralization with soda ash. If surface is unusually soft, painted, peeling or flaking, then surface must be heavily sanded or water blasted. Regardless of method used, thoroughly wash down with “jet nozzle” hose and let pool drain until there is no standing water present. NOTE: Special attention is required on pools below water table and or leaking. MIXING: • Make sure “liquid resin” is mechanically agitated before use to disperse all settled solids. • Then pour “liquid resin” (5 gallon) into a clean mixing container with flat bottom. Add Bond Kote (two 65 lb. bags) while continuously mixing with echanical mixer. Continue mixing for 2-4 minutes until Bond Kote is completely dispersed. NEVER USE LESS • THAN 115 lbs. OF DRY MIX PER 5 GALLONS OF LIQUID RESIN. APPLICATIONS: To check consistency of material, apply Bond Kote with 1-1/4″ nap roller onto a vertical test area. Let material set for 1 minute; then, using a clean textured roller, rough up surface to desired finish. Material thickness can be adjusted by adding a small amount of “cement mix” if too thin or “liquid resin” if too thick, adjust only 1 time. DO NOT RETEMPER MIX. Once Bond Kote is mixed to correct consistency, apply immediately, do not let material stand unused. Apply, mixed Bond Kote with 1-1/4″ nap roller to steps at shallow end of pool and let material set for approximately 1 minute; then, rough up surface to desired finish with clean textured roller as done in test area. Continue this same process with the wall areas and then proceed to the floor surface last. Starting at deep end of pool make sure application is uniform in thickness and texture. CURING: Minimum cure is reached in 6 hours; setting and drying time may vary according to atmospheric conditions. For best results wait 24 hours before plastering. PLASTERING: Mist Bond Kote with clean cool water prior to plastering to permit proper hydration. Make sure Bond Kote is free of any foreign matter before plastering. COVERING: One unit covers 450-500 square feet of surface area. CLEAN UP/STORAGE: Clean hands, tools and containers with warm soapy water. NOTE: USE NEW ROLLER WITH EACH APPLICATION.

Price: $88.40

Loading Updating cart…

Pebble Beach.

Color Pebble Beach.
Each Bag = 80 Pounds.
Minimum order of 30 Bags if out of South Florida Area.

Additional DescriptionMore Details

Blends of selected natural aggregates and fortified Portland cement, ideal for new or refinished swimming pools. Available in a variety of colors, River Rok finishes are factory blended to provide the pool owner with an extremely durable and attractive alternative to traditional pool coatings. ADVANTAGES: •Superior Bonding •High strength and rapid curing •Extremely etch resistant COVERAGE: Each 80lb.bag will cover approximately 18 sq. ft. to a thickness of ½”. Substrate texture will affect coverage rates. PACKAGING: 4 ply heavy duty poly-lined bad, net wt. 80 lb. LIMITED WARRANTY: S.G.M., Inc., will replace any material proved defective with the maximum shelf life on unused material of up to one (1) year. If our products are not found to conform to our high standards, notify S.G.M., Inc., immediately in writing. There is no other obligation expressed or implied, and we assume no liabilities for damages of any kind. Suitability of the product for an intended use shall be solely up to the user.

Price: $29.09

Loading Updating cart…

Lucayan Blue.

Color Lucayan Blue.
Each Bag = 80 Pounds.
Minimum order of 30 Bags if out of South Florida Area.

Additional DescriptionMore Details

Blends of selected natural aggregates and fortified Portland cement, ideal for new or refinished swimming pools. Available in a variety of colors, River Rok finishes are factory blended to provide the pool owner with an extremely durable and attractive alternative to traditional pool coatings. ADVANTAGES: •Superior Bonding •High strength and rapid curing •Extremely etch resistant COVERAGE: Each 80lb.bag will cover approximately 18 sq. ft. to a thickness of ½”. Substrate texture will affect coverage rates. PACKAGING: 4 ply heavy duty poly-lined bad, net wt. 80 lb. LIMITED WARRANTY: S.G.M., Inc., will replace any material proved defective with the maximum shelf life on unused material of up to one (1) year. If our products are not found to conform to our high standards, notify S.G.M., Inc., immediately in writing. There is no other obligation expressed or implied, and we assume no liabilities for damages of any kind. Suitability of the product for an intended use shall be solely up to the user.

Price: $40.29

Loading Updating cart…

Imperial White.

Color Imperial White.
Each Bag = 80 Pounds.
Minimum order of 30 Bags if out of South Florida Area.

Additional DescriptionMore Details

Blends of selected natural aggregates and fortified Portland cement, ideal for new or refinished swimming pools. Available in a variety of colors, River Rok finishes are factory blended to provide the pool owner with an extremely durable and attractive alternative to traditional pool coatings. ADVANTAGES: •Superior Bonding •High strength and rapid curing •Extremely etch resistant COVERAGE: Each 80lb.bag will cover approximately 18 sq. ft. to a thickness of ½”. Substrate texture will affect coverage rates. PACKAGING: 4 ply heavy duty poly-lined bad, net wt. 80 lb. LIMITED WARRANTY: S.G.M., Inc., will replace any material proved defective with the maximum shelf life on unused material of up to one (1) year. If our products are not found to conform to our high standards, notify S.G.M., Inc., immediately in writing. There is no other obligation expressed or implied, and we assume no liabilities for damages of any kind. Suitability of the product for an intended use shall be solely up to the user.

Price: $25.74

Loading Updating cart…

Granite.

Color Granite.
Each Bag = 80 Pounds.
Minimum order of 30 Bags if out of South Florida Area.

Additional DescriptionMore Details

Blends of selected natural aggregates and fortified Portland cement, ideal for new or refinished swimming pools. Available in a variety of colors, River Rok finishes are factory blended to provide the pool owner with an extremely durable and attractive alternative to traditional pool coatings. ADVANTAGES: •Superior Bonding •High strength and rapid curing •Extremely etch resistant COVERAGE: Each 80lb.bag will cover approximately 18 sq. ft. to a thickness of ½”. Substrate texture will affect coverage rates. PACKAGING: 4 ply heavy duty poly-lined bad, net wt. 80 lb. LIMITED WARRANTY: S.G.M., Inc., will replace any material proved defective with the maximum shelf life on unused material of up to one (1) year. If our products are not found to conform to our high standards, notify S.G.M., Inc., immediately in writing. There is no other obligation expressed or implied, and we assume no liabilities for damages of any kind. Suitability of the product for an intended use shall be solely up to the user.

Price: $25.74

Loading Updating cart…

Emerald Black.

Color Emerald Black.
Each Bag = 80 Pounds.
Minimum order of 30 Bags if out of South Florida Area.

Additional DescriptionMore Details

Blends of selected natural aggregates and fortified Portland cement, ideal for new or refinished swimming pools. Available in a variety of colors, River Rok finishes are factory blended to provide the pool owner with an extremely durable and attractive alternative to traditional pool coatings. ADVANTAGES: •Superior Bonding •High strength and rapid curing •Extremely etch resistant COVERAGE: Each 80lb.bag will cover approximately 18 sq. ft. to a thickness of ½”. Substrate texture will affect coverage rates. PACKAGING: 4 ply heavy duty poly-lined bad, net wt. 80 lb. LIMITED WARRANTY: S.G.M., Inc., will replace any material proved defective with the maximum shelf life on unused material of up to one (1) year. If our products are not found to conform to our high standards, notify S.G.M., Inc., immediately in writing. There is no other obligation expressed or implied, and we assume no liabilities for damages of any kind. Suitability of the product for an intended use shall be solely up to the user.

Price: $35.98

Loading Updating cart…

Calm Sea.

Color Calm Sea.
Each Bag = 80 Pounds.
Minimum order of 30 Bags if out of South Florida Area.

Additional DescriptionMore Details

Blends of selected natural aggregates and fortified Portland cement, ideal for new or refinished swimming pools. Available in a variety of colors, River Rok finishes are factory blended to provide the pool owner with an extremely durable and attractive alternative to traditional pool coatings. ADVANTAGES: •Superior Bonding •High strength and rapid curing •Extremely etch resistant COVERAGE: Each 80lb.bag will cover approximately 18 sq. ft. to a thickness of ½”. Substrate texture will affect coverage rates. PACKAGING: 4 ply heavy duty poly-lined bad, net wt. 80 lb. LIMITED WARRANTY: S.G.M., Inc., will replace any material proved defective with the maximum shelf life on unused material of up to one (1) year. If our products are not found to conform to our high standards, notify S.G.M., Inc., immediately in writing. There is no other obligation expressed or implied, and we assume no liabilities for damages of any kind. Suitability of the product for an intended use shall be solely up to the user.

Price: $34.24

Loading Updating cart…

Sea Foam.

Color Sea Foam.
Each bag =80 Pounds.
Minimum order of 30 Bags if out of South Florida Area.

Additional DescriptionMore Details

Durazzo Offer an optimal range of color designs that are factory to perfection. Your pool can become an axtension of your dreams. And if you are so inclined, you can even custom bled our premium finish to invent an exquisite poolscape that truly begest originality. Ask you pool representative for a complete presentation of our product line. Advatages: Pre-Blended/Ready to use, confortable, smooth, variety of colors, reduces maintenance, and ease of applications. Specification: Complete three-part master specifications are available for Durazzo installations. Contact you pool representative for details. Warranty: You can rest assured that the highest quality products have been used and is supported by the best warranty program in the industry. It is a sign of our commitment to archive the highest quality standards in all our swimming pool and spa finishes.

Price: $25.42

Loading Updating cart…

Sandy Beach.

Color Sandy Beach.
Each Bag = 80 Pounds.
Minimum order of 30 Bags if out of South Florida Area.

Additional DescriptionMore Details

Durazzo Offer an optimal range of color designs that are factory to perfection. Your pool can become an axtension of your dreams. And if you are so inclined, you can even custom bled our premium finish to invent an exquisite poolscape that truly begest originality. Ask you pool representative for a complete presentation of our product line. Advatages: Pre-Blended/Ready to use, confortable, smooth, variety of colors, reduces maintenance, and ease of applications. Specification: Complete three-part master specifications are available for Durazzo installations. Contact you pool representative for details. Warranty: You can rest assured that the highest quality products have been used and is supported by the best warranty program in the industry. It is a sign of our commitment to archive the highest quality standards in all our swimming pool and spa finishes.

Price: $21.52

Loading Updating cart…
Pages: 1 2 3 4Next >Last »
We accept the following credit cards